My Blog

Category: Charger

  • 2021 Dodge Charger SRT Hellcat – Stage-2 Hellcat Power Package Makes 900hp+ On Pump Gas!

    2021 Dodge Charger SRT Hellcat – Stage-2 Hellcat Power Package Makes 900hp+ On Pump Gas!

    It’s no secret that we absolutely love the SRT Hellcat lineup!  Whether you choose Challenger, Charger, Durango, Trackhawk, or TRX, each are a killer performance package right off the showroom floor.  But to us, we don’t believe in leaving well enough alone, especially when there’s cheap and reliable horsepower to be had!  And if you’re reading this article, then chances are you’re right there with us.

     

     

    This is the reason that our Stage-1 Hellcat Power Package for these vehicles is one of most popular we offer!  Serious power increase, without any impact on drivability or reliability.  This package is proven to add up to 140hp at the tires on 93 octane pump gas, and in most cases, exceed the 800whp mark without breaking a sweat.  You can learn more about this package by watching the video below:

     

     

    But what about those who want to go a little bit further, while still maintaining stock-like drivability and reliability?  That’s where our Stage-2 package comes into play!  Using our Stage-1 package as the foundation, our Stage-2 Hellcat Power Package takes it up a notch with the addition of supercharger porting, larger diameter throttle body, and higher flowing mid-pipe complete with EPA compliant catalytic converters which support over 1,000hp!  How much of an impact does this have on the dyno?  Gains of up to 180hp over stock baseline, on 93 octane pump gas!  Full contents below:

     

    • National Speed in-house PCM unlocking service
    • Stainless Works 3.00″ ID mid-pipe
    • GESi G-Sport EPA compliant GEN2 HO (High Output) high-flow catalytic converters which support up to 500hp per core
    • JLT Performance 125mm air-intake system
    • Metco Motorsports 2.85” upper supercharger pulley
    • TBA Machine 3.00″ dual-bearing supercharger idler pulley
    • TBA Machine 3.00″ supercharger tensioner pulley
    • Pinned harmonic balancer
    • Gates HD Fleetrunner Micro-V “Green” belt
    • Kong Performance ported supercharger & inlet port matched to 108mm throttle body
    • Kong Performance 108mm throttle body
    • Properly gapped NGK LFR7AIX spark plugs
    • Injector Dynamics ID1050x fuel injectors
    • Optional MotoRad 180° thermostat
    • Optional J&L OSC air-oil separator
    • Optional Borla exhaust system
    • Genuine OEM Mopar components required for installation
    • HP Tuners Smart Access cable
    • HP Tuners credits
    • Custom National Speed calibration on the dyno
     
    And this package is exactly what Adam wanted for his brand new, showroom stock 2021 Dodge Charger SRT Hellcat Widebody!
     

     

    And the great thing is that this stock engine bay won’t appear dramatically different after all of this work!

     

     

    HP Tuners Smart Access cable being installed for the initial read prior to PCM unlocking…

     

     

    Supercharger off to porting!

     

     

    See the oil buildup in the intake ports?  This car is brand new, and it’s already accumulated that much!  This is why the J&L OSC air-oil separator is a strongly recommended option…

     

     

    The Kong Performance 108mm throttle body…

     

     

    Injector Dynamics ID1050x fuel injectors going in…

     

     

    The finished result!  Crazy to think the under-hood aesthetic is mostly stock appearing, but is packing 180hp extra…

     

     

     

    And the result?  With a stock baseline of 664.44whp & 648.66lbft, our Stage-2 package increases output to a blistering 847.45whp & 751.57lbft on 93 octane pump gas!  Peak gains of 183.01whp & 102.91lbft, all without compromising drivability or reliability.  Absolutely killer performance!

     

     

    Contact Us to Discuss Your Next Project

  • 2018 Dodge Charger SRT 392 – Stage-1 ProCharger

    2018 Dodge Charger SRT 392 – Stage-1 ProCharger

     
    Lance brought us his 2018 Dodge Charger SRT 392 to have the 6.4L Hemi set up with our Stage-1 ProCharger supercharger package! 

    Modifications below:

    • National Speed in-house Mopar ECU unlocking service
    • ProCharger Superchargers P-1SC-1 High Output supercharger system
    • ProCharger Superchargers front-mount intercooler
    • NGK Spark Plugs LFR6AIX-11 spark plugs
    • MotoRad 180° thermostat
    • J&L Oil Separator Co. OSC 3.0 air/oil separator
    • Walbro 450lph in-tank fuel pump
    With the mechanical work wrapped up in the shop by Dylan, Matt strapped her down to the rollers for a custom calibration by Taylor via HP Tuners. With 93 octane in the tank, Taylor increased output to 628.20whp & 568.40lbft!

     
     
     
     
     
     
     
     
     

  • 2021 Dodge Charger R/T Scat Pack – Stage 1 NA Package

    2021 Dodge Charger R/T Scat Pack – Stage 1 NA Package

    Lance brought us his 2021 Dodge Charger R/T Scat Pack for our Stage-1 package! This setup adds noticeable performance, engine induction noise, and can be done in less than a day! Fantastic starting point for any Mopar vehicle.
     
    Package contents below:
    • JLT Performance air-intake system
    • National Speed in-house ECU unlock
    • SmartAccess cable
    • Custom calibration via HP Tuners
     
    With the mechanical work wrapped up in the shop by Dylan, Matt strapped her down to the rollers for a custom calibration by Vlad via HP Tuners. With 93 octane in the tank, Vlad increased the 6.4L Hemi’s output to 470.24whp & 483.17lbft. Freakishly strong performance for a 6.4L Hemi with the modifications performed!

  • 2014 Chrysler 300C SRT8 – COMP Cams Stage 2 Install

    2014 Chrysler 300C SRT8 – COMP Cams Stage 2 Install

    Thomas brought us his 2014 Chrysler 300C SRT8 to get the 6.4L Hemi set up with our camshaft package, and address an MDS lifter failure!
     
    Modifications below:
    • COMP Cams Stage-2 HRT 273° camshaft
    • COMP Cams phase-limiter kit
    • COMP Cams pushrods
    • COMP Cams valve seats, valve seals, valve springs, valve retainers & locks
    • MDS delete utilizing OEM Mopar components
    • OEM Hellcat lifters
    • OEM Hellcat engine oil pump
    • NGK Spark Plugs LZTR6AIX-13 spark plugs
    • All the miscellaneous OEM and aftermarket odds-and-ends to bring it all together
     
    With the mechanical work wrapped up in the shop by Dylan, Matt strapped her down to the rollers for Vlad to perform a custom calibration via HP Tuners. With 93 octane in the tank, Vlad increased the 6.4L Hemi’s output to 443.07whp & 460.72lbft through a 100% stock exhaust and intake system!

  • 2018 Dodge Charger Daytona – Stage 3 Package

    2018 Dodge Charger Daytona – Stage 3 Package

    William brought us his 2018 Dodge Charger Daytona for our Stage-3 Naturally Aspirated package to get the 5.7L Hemi bumping and breathing better!
     
    Modifications performed by us below:
    • COMP Cams Stage-2 HRT 273° camshaft
    • COMP Cams phase-limiter kit
    • COMP Cams pushrods
    • COMP Cams valve seats, valve seals, valve springs, valve retainers & locks
    • MDS delete utilizing OEM Mopar components
    • OEM Hellcat lifters
    • OEM Hellcat engine oil pump
    • Kooks Headers and Exhaust long-tubes headers with high-flow catalytic converters
    • Kooks Headers and Exhaust exhaust system
    • NGK Spark Plugs LFR6AIX-11 spark plugs
    • MotoRad 180° Thermostat
    • All the miscellaneous OEM and aftermarket odds-and-ends to bring it all together
    • HP Tuners SmartAccess cable
    • In-house Mopar ECU unlocking service
     
    With the mechanical work wrapped up in the shop by Andrew, Matt strapped her down to the rollers for Vlad to perform a custom calibration via HP Tuners. With 93 octane in the tank, Vlad increased the 5.7L Hemi’s output to 433.73whp & 435.02lbft!

  • 2019 Dodge Charger R/T Scat Pack – Whipple Supercharged

    2019 Dodge Charger R/T Scat Pack – Whipple Supercharged

    Hadriann brought us his 2019 Dodge Charger R/T Scat Pack to get the 6.4L Hemi Whipple supercharged and over the 600whp mark! Modifications performed by us below:
     
    • Whipple Superchargers Stage-II 2.9L W175AX twin-screw system
    • Whipple Superchargers upgraded air-intake system
    • DeatschWerks 65lb fuel injectors
    • MSD Performance fuel pump voltage booster
    • MotoRad 180° thermostat
    • NGK Spark Plugs LZTR7AIX spark plugs
    • JLT Performance air-oil separator
    • HP Tuners unlocked ECU
    • All the miscellaneous OEM and aftermarket components to bring it all together
     
    With the mechanical work wrapped up, John strapped her down to the rollers for Vlad to perform a custom calibration via HP Tuners. With the Whipple 2.9L delivering ~9psi, Vlad increased the 392’s output to a solid 642.38whp & 587.06lbft!
     
     
     
     
     
     
     
     
    Reach Out Today To See What We Can Do For You!

     

    Contact Us
  • 2020 Dodge Charger 392 Scat Pack – 500whp

    2020 Dodge Charger 392 Scat Pack – 500whp

     

    Lamont brought us his 2020 Dodge Charger 392 Scat Pack to have the 6.4L Hemi equipped with our 500whp+ camshaft package! Modifications below:

    Pre-existing:
    • JLT Performance air-intake system
    • Ported OEM intake manifold
    • Fast Man 86mm throttle body
    • 180° thermostat

    Performed by us:
    • COMP Cams camshaft
    • COMP Cams phase-limiter kit
    • COMP Cams pushrods
    • COMP Cams Beehive valve springs
    • COMP Cams valve lock set
    • COMP Cams spring seats
    • COMP Cams positive stop PTFE valve seals
    • OEM Mopar Hellcat lifters
    • OEM Mopar Hellcat engine oil pump
    • OEM Mopar Hellcat fuel injectors
    • MDS delete utilizing OEM Mopar components

    With the mechanical work wrapped up in the shop by John, Matt strapped her down to the rollers for Vlad to perform a custom two-fuel calibration via HP Tuners. Up first with 93 octane in the tank, Vlad increased the 6.4L’s output to 512.52whp & 512.91lbft, and then with E85 in the tank, output increased to a 525.94whp & 530.11lbft! Definitely a solid outcome that Lamont is sure to enjoy.

     
    Reach Out Today To See What We Can Do For You!

     

    Contact Us
  • 2017 Dodge Charger SRT 392 – Whipple Supercharged

    2017 Dodge Charger SRT 392 – Whipple Supercharged

    Jared brought us his 2017 Dodge Charger SRT 392 to get the 6.4L Hemi Whipple supercharged and over the 600whp mark! Modifications performed below:
     
    • Whipple Superchargers Stage-II 2.9L W175AX twin-screw system
    • Whipple Superchargers upgraded air-intake system
    • DeatschWerks 65lb fuel injectors
    • MSD Performance fuel pump voltage booster
    • NGK Spark Plugs LZTR7AIX spark plugs
    • HP Tuners unlocked ECU
    • All the miscellaneous OEM and aftermarket components to bring it all together
     
    With the mechanical work wrapped up, Matt strapped her down to the rollers for Vlad to perform a custom calibration via HP Tuners. With the Whipple 2.9L delivering ~8psi, and a 100% factory exhaust system in place, Vlad increased the 392’s output to a repeatable 611.10whp & 571.81lbft!
     

     
    Reach Out Today To See What We Can Do For You!

     

    Contact Us
  • 2018 Dodge Charger SRT Hellcat – 800whp

    2018 Dodge Charger SRT Hellcat – 800whp

    All the way in from Florida, Samuel brought us his 2018 Dodge Charger SRT Hellcat to get her turned up to 800whp!

    Up first in the shop, John strapped her down for pre-work dyno runs to establish our starting point, coming in at 643.65whp & 616.15lbft. From there, TJ set the supercharged 6.2L HEMI up with an air-intake system from JLT Performance, 2.75″ upper supercharger pulley & billet idler from Metco Motorsports, a Gates HD Fleetrunner Micro-V “Green” serpentine belt, along with a pinned harmonic balancer for extra assurance, a set of 2.00″ primary diameter long-tube headers from Stainless Works, OEM Dodge Demon fuel injectors, and a 180° thermostat from MotoRad.

    With the mechanical work wrapped in the shop, John strapped her back down to the rollers for Vlad to perform a custom calibration via HP Tuners. With 93 octane in the tank, and the IHI 2.4L supercharger delivering 15psi, Vlad increased output to 803.80whp & 751.63lbft — a gain of 160.15whp & 135.48lbft! From there, Samuel picked her up for the long drive home, and has been having a blast back home in Florida!

    Reach Out Today To See What We Can Do For You!
    Contact Us
  • 2016 Dodge Charger SRT Hellcat

    2016 Dodge Charger SRT Hellcat

    Romeo brought us his 2016 Dodge Charger SRT Hellcat for the first round of modifications!

    Up first in the shop, John set the supercharged 6.2L HEMI up with an air-intake system and air-oil separator from JLT Performance, 2.75″ upper supercharger pulley & billet idler from Metco Motorsports, a Gates HD Fleetrunner Micro-V “Green” serpentine belt, a set of 2.00″ primary diameter long-tube headers from Stainless Works, ID1050X fuel injectors from Injector Dynamics, and a 180° thermostat from Mishimoto Automotive.

    With the mechanical work wrapped in the shop, Matt strapped her down to the rollers for Vlad to perform a custom calibration via HP Tuners. The results? With 93 octane in the tank, and the IHI 2.4L supercharger delivering 15psi, Vlad increased output to 787.87whp & 720.11lbft! The extra ~120whp, supercharger whine, and exhaust note should definitely make the daily commute far more interesting.

    Reach Out Today To See What We Can Do For You!