Category: Subaru

  • 2014 Subaru WRX – IAG Short Block

    2014 Subaru WRX – IAG Short Block

    Nick brought us his 2014 Subaru WRX to have the EJ257 built and ready for many miles of enjoyment!
     
    Build setup below:
    IAG Performance Stage 2 EJ257 short block
    IAG Performance wrist pin & cover seal kit
    ARP 2000 series cylinder head studs
    IAG Performance V2 stainless steel oil pickup
    • WRX STI 11mm oil pump
    • OEM Subaru oil pan, oil cooler, and associated components
    • OEM Subaru timing components
    IAG Performance Street Series air/oil separator
    • OEM Subaru IHI VF52 turbocharger
    IAG Performance turbocharger oil feed and AVCS oil lines
    NGK Spark Plugs LFR7AIX spark plugs
    Advanced Clutch Technology Streetlite flywheel
    COBB Tuning Accessport V3
    • All the miscellaneous OEM Subaru gaskets, seals, and components to complete the installation
     
    Pre-existing:
    • Downpipe w/ high-flow catalytic converter
    COBB Tuning cold-air-intake system
    Process West top-mount intercooler
     
    With the mechanical work wrapped up by Andrew in the shop, Matt strapped her down to the rollers for Vlad to perform a custom calibration via COBB Tuning‘s Accessport V3. With 93 octane in the tank, Vlad increased the EJ257’s output to 313.70awhp & 342.80lbft! Solid pump gas performance that Nick is sure to enjoy!

  • 2015 Subaru WRX – IAG & Cobb Parts Install

    2015 Subaru WRX – IAG & Cobb Parts Install

    There were several pre-existing modifications already in place on Nate’s Lightning Red 2015 WRX. The plan was to add some additional bolt-on performance, and to get the FA20DIT dialed in by Vlad via COBB Tuning‘s Accessport V3!
     
    Modifications performed by us below:
    COBB Tuning top-mount intercooler
    IAG Performance Street Series air-oil separator
    NGK Spark Plugs ILKAR8H6 Spark Plugs
     
    Pre-existing:
    GrimmSpeed 3-port electronic boost control solenoid
    PERRIN Performance turbo inlet pipe
    Mishimoto Automotive charge pipes
    Mishimoto Automotive resonated downpipe
    COBB Tuning SF air-intake system
     
    With the mechanical work wrapped up in the shop by John, Matt strapped her down to the rollers for Vlad to perform a custom calibration via COBB Tuning‘s Accessport V3. With 93 octane in the tank, Vlad increased the FA20DIT’s output to 314.05awhp & 337.61lbft! Solid numbers coming out of this stock-turbo ’15 WRX!

  • 2007 Subaru Impreza WRX STI – Reliability Mods

    2007 Subaru Impreza WRX STI – Reliability Mods

    It’s not that often the older generations receive the much deserved love that the newer generations get. Take in account Brian’s extremely well kept 2007 Subaru Impreza WRX STI. Sitting at just over 100k miles and finished in flawless, all original Urban Gray Metallic paint, this tastefully modified GD Hawkeye has survived the test of time, proving that with the right caretaker, the older generations can look just as good as the newest models.

    While this Hawkeye has maintained a fairly stock life so far, reliability modifications are always encouraged, so Brian brought his car to turn it up a hair and to keep things running smoothly for some future track use. Modifications performed by us below:

    COBB Tuning 3-port electronic boost control solenoid
    COBB Tuning AccessPort V3
    GrimmSpeed 3″ FXT downpipe w/ high flow catalytic converter

    With the mechanical work wrapped up in the shop by Andrew, Matt strapped her down to the rollers for Vlad to perform a custom calibration via COBB Tuning Accessport V3. With the stock turbocharger delivering ~19psi, Vlad increased the EJ257’s output to a solid 313.61awhp & 336.05lbft!

     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
    Reach Out Today To See What We Can Do For You!

     

     
     

     

  • Golden Power: Victor White’s 815whp 2008 Subaru STI

    Golden Power: Victor White’s 815whp 2008 Subaru STI

     

    One of the best parts of being in the automotive community and building cars is seeing the different evolutions and phases of builds through the years. Victor White’s Subaru STI is a great example of this. 

     

    Victor came to us with his 2008 Subaru STI ready for the next phase of its life, going from a built motor to an insane IAG Tuff Stage 4 Short Block with Stage 5 heads with a big Precision 6870 Turbo.

     

     

    We were as excited as Victor was for this next phase of his GR STI, so we pulled it in and got to work! First things first, out went the old built motor, ready for it’s next life in a new chassis, and we started getting the bay ready for the new IAG Performance Short Block. Topping off the motor is a Process West intake manifold alongside the massive 6870 Turbo from Precision Turbo and 44m waste gates from TiAL. 

     

    As we assembled the block, we couldn’t help but admire how great it looked. There’s something about engine components that strike the eye just right.

     

     

     Even with as good as it looked, Victor wanted to take the aesthetics to the next level. To match his gold wheels and set off the engine bay, the IAG Fuel Rails and top feed TGV housings were anodized gold. 

     

     

    To fuel this golden powerplant, twin Walbro 450lph fuel pumps were installed and run with a COBB tuning flex fuel kit in order to make the most of the E85 compatibility and potential power gains. 


    With big power Subaru builds like this, the factory top mounted intercooler just doesn’t get the air needed to keep the engine cool and in proper boost, so we tapped the team at Extreme Turbo Systems for a front mount intercooler kit, powdercoated gold to match the rest of the accent pieces.

     

     

    Sometimes, custom builds require custom work, and that’s where our custom fabricating team comes in handy! Our Performance Technician, Alex, got to work fabricating everything needed to finish up the build, from a custom fabricated coolant reservoir to fuel lines and turbo piping. With Alex’s custom work and some fittings from Vibrant Performance, Fragola Performance, and Radium Engineering, the motor was ready to go!

     

    With the motor buttoned up, turbo piped up, and intercooler mounted in the front, it was time to move on to supporting the boosted bomb under the hood. 

     

     

    To help the transmission handle the boost in power, we installed chromoly billet transfer gears along with a triple disk competition clutch and flywheel from IAG Performance. DSS Axles were also installed to help put the power down to all four wheels. 

     

    Keeping the build functional and just as good as stopping as going, the brakes were swapped out for EBS Brakes GD Rotors and Yellow Stuff Pads. Running to each corner are stainless steel brake lines from StopTech. 

     

     

    With the build all set, the only thing left was to get tuning. We strapped the STI on the rollers and let it rip!

     

    After working the COBB Accessport and laying down an impressive 816whp and 669lb/ft of torque on E85, Victor’s STI was reborn into its new phase of life, as an absolute monster! 

     

     

    We love being able to help other enthusiasts make their performance dreams a reality, and Victor’s build was another great example of that! We can’t wait to see what else he has in store for his STI hatch.

     Parts List: 

    • IAG STAGE 4 TUFF EJ25 SUBARU CLOSED DECK SHORT BLOCK FOR WRX, STI, LEGACY GT, FORESTER XT
    • IAG Performance Competition Triple Disk Clutch and Flywheel
    • IAG Billet Transfer Gears
    • Precision Turbo 6870 Turbocharger
    • StopTech stainless steel brake lines
    • OEM subaru baskets and components
    • LFR7AIX Spark Plugs
    • ARP 2000 Series Head Studs
    • EBC Brakes GD Rotors and Yellow Stuff Pads
    • Twin Walbro 450lph fuel pump – E85 compatible
    • Gold Anodized IAG cnc top feed tgv housings
    • Gold Anodized  IAG Fuel Rails 
    • Gold Anodized Extreme Turbo Systems Front Mount Intercooler
    • TiAL 44mm Waste gate valves (black)
    • Cobb Flex Fuel kit,ethanol content sensor, fuel pressure sensor kit, 
    • ATI Performance Super Damper Crank Pulley
    • Fragola hoses & PTFE fittings
    • Vibrant Performance Aluminum Vbands and fittings.

    For a closer look at this build, take a look at the gallery below. 

    [ngg src=”galleries” ids=”492″ display=”basic_thumbnail” thumbnail_crop=”0″]

     

  • 2014 Subaru WRX STI- IAG Stage 2 EJ257

    2014 Subaru WRX STI- IAG Stage 2 EJ257

    Jeff brought us his 2014 Subaru WRX STI to have the EJ257 built and taken up a notch! Build setup below:
     
    IAG Performance Stage 2 Tuff EJ257 short block
    ARP 2000 series cylinder head studs
    IAG Performance V2 stainless steel oil pickup
    • WRX STI 11mm oil pump
    • OEM Subaru oil pan, oil cooler, and associated components
    • OEM Subaru timing components
    IAG Performance Street Series air/oil separator
    Garrett – Advancing Motion GT3076R turbocharger
    COBB Tuning turbo blanket
    COBB Tuning black silicone turbo inlet
    COBB Tuning SF air-intake system
    COBB Tuning down-pipe exhaust system
    COBB Tuning exhaust system
    Extreme Turbo Systems front-mount intercooler
    COBB Tuning XLE bypass valve
    Injector Dynamics ID1300x fuel injectors
    AEM Performance Electronics 320lph in-tank fuel pump
    COBB Tuning fuel pressure regulator kit
    NGK Spark Plugs SILFR6A spark plugs
    Advanced Clutch Technology HDSS clutch
    Advanced Clutch Technology Streetlite flywheel
    COBB Tuning 3-port electronic boost control solenoid
    COBB Tuning 4bar MAP sensor
    • All the miscellaneous OEM Subaru gaskets, seals, and components to complete the installation
     
    With the mechanical work wrapped up by Andrew in the shop, Matt strapped her down to the rollers for Vlad to perform a custom calibration via COBB Tuning‘s Accessport V3. With 93 octane in the tank, Vlad increased the EJ257’s output to 388.16awhp & 381.15lbft! Solid pump gas performance that Jeff is sure to enjoy!
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
    Reach Out Today To See What We Can Do For You!

     

  • 2018 Subaru BRZ- SBD Turbo Kit

    2018 Subaru BRZ- SBD Turbo Kit

    It’s undeniable that the FR-S/BRZ/GT86 is one seriously fun driver’s car, but the resounding feedback from owners and critics alike is that the car’s missing a little something in factory form… BOOST! Jennifer shares that sentiment, and brought us her 2018 Subaru BRZ to address it! Modifications performed below:
     
    Speed By Design LLC G500X turbocharger system
    Advanced Clutch Technology HDSS clutch
    Invidia Exhaust Gemini R400 exhaust system
     
    With the mechanical work wrapped in the shop by Alex, Matt strapped her down to the rollers for Vlad to perform custom calibration via EcuTek Technologies Ltd. With 93 octane in the tank, Vlad was able to increase the FA20’s output to 317.41whp & 245.49lbft! Given that Jennifer’s feedback after deliver was, “you guys are the best! I’ve been giggling since I left!” we’d say she’s enjoying the result!
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
    Reach Out Today To See What We Can Do For You!

     

  • 2019 Subaru WRX STI – 400awhp

    2019 Subaru WRX STI – 400awhp

    Patrick brought us his 2019 Subaru WRX STI to have the EJ257 built, Flex Fuel enabled, and taken to 400awhp! Build setup below:
     
    IAG Performance Stage 2 Tuff EJ257 short block
    ARP 2000 series cylinder head studs
    IAG Performance V2 stainless steel oil pickup
    • WRX STI 11mm oil pump
    IAG Performance Street Series air/oil separator
    AEM Intakes air-intake system
    Invidia Exhaust down-pipe connecting to the existing Gemini R400 exhaust system
    Extreme Turbo Systems top-mount intercooler
    Injector Dynamics ID1050x fuel injectors
    Blouch Turbo 20G-XT turbocharger
    NGK Spark Plugs LFR7AIX spark plugs
    Advanced Clutch Technology XTSS clutch
    Advanced Clutch Technology Streetlite flywheel
    COBB Tuning 3-port electronic boost control solenoid
    COBB Tuning Flex Fuel conversion
    • All the miscellaneous OEM Subaru gaskets, seals, and components to complete the installation
     
    With the mechanical work wrapped up by Dylan in the shop, John strapped her down to the rollers for Vlad to perform a custom calibration via COBB Tuning‘s Accessport V3. With 93 octane in the tank, Vlad increased the EJ257’s output to 385.32awhp & 358.11lbft, and after switching to E85, output jumped to 403.24awhp & 410.14lbft! Nice square setup with usable power all over the rev range!
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
    Reach Out Today To See What We Can Do For You!

     

  • 2019 Subaru WRX – Bolt-ons & Tune

    2019 Subaru WRX – Bolt-ons & Tune

    Ben brought us his beautiful 2019 Subaru WRX for some bolt-on performance and to get the FA20DIT dialed in by Vlad via COBB Tuning’s Accessport V3! Modifications performed by us below:
     
    GrimmSpeed Stealthbox air-intake system
    IAG Performance Street Series air-oil separator
    COBB Tuning 3-port electronic boost control solenoid
    Invidia Exhaust J-pipe
     
    With the mechanical work wrapped up in the shop by Alex, Matt strapped her down to the rollers for Vlad to perform a custom calibration via COBB Tuning’s Accessport V3. With 93 octane in the tank, Vlad increased the FA20DIT’s output to 304.14awhp & 326.28lbft!
     
     
     

     
    Reach Out Today To See What We Can Do For You!

     

  • 2009 Subaru WRX – IAG Short Block Refresh

    2009 Subaru WRX – IAG Short Block Refresh

    Sherman brought us his 2009 Subaru WRX for an IAG Performance short block and to have Vlad dial the EJ255 in via COBB Tuning’s Accessport V3! Build details below:
     
    Pre-existing:
    COBB Tuning exhaust and down-pipe
    COBB Tuning SF air-intake system
    COBB Tuning bypass valve
     
    Performed by us:
    IAG Performance Stage 1 EJ257 short block
    ARP 2000 series cylinder head studs
    • OEM STI 11mm oil pump
    IAG Performance V2 oil pump pickup tube
    IAG Performance Street Series air/oil separator
    PERRIN Performance turbocharger inlet tube
    EXEDY USA clutch kit
    EXEDY USA flywheel
    NGK Spark Plugs spark plugs
    • All the miscellaneous OEM Subaru gaskets, seals, and timing components to complete the installation
     
    With the mechanical work wrapped up by Michael in the shop, John strapped her down to the rollers for Vlad to perform a custom calibration via COBB Tuning’s Accessport V3. With 93 octane in the tank, Vlad increased the EJ255’s output to 287.11awhp & 324.65lbft!
     

     
    Reach Out Today To See What We Can Do For You!

     

  • 2019 Subaru WRX STI  – IAG Stage 2.5

    2019 Subaru WRX STI – IAG Stage 2.5

    Brad brought us his beautiful 2019 Subaru WRX STI for a built engine and max-effort stock turbocharger setup! Build details below:
     
    Pre-existing:
    K&N Filters cold air intake system
     
    Performed by us:
    IAG Performance Stage 2.5 EJ25 closed deck short block
    ARP 2000 series cylinder head studs
    IAG Performance Street Series air/oil separator
    COBB Tuning turbocharger inlet
    GrimmSpeed 3-port electronic boost control solenoid
    Getadomtune cylinder 4 chamber cooling system
    IAG Performance V2 oil pump pickup tube
    • STI 11mm oil pump
    NGK Spark Plugs LFR7AIX spark plugs
    IAG Performance PTFE Flex Fuel fuel system with gold fuel rails
    Injector Dynamics ID1700x Injectors
    COBB Tuning Flex Fuel conversion
    AEM Performance Electronics 320lph in-tank fuel pump
    Advanced Clutch Technology HDSS clutch kit
    Advanced Clutch Technology Streetlite flywheel
    Invidia Exhaust down-pipe
    Invidia Exhaust Q300 exhaust system
    • All the miscellaneous OEM Subaru gaskets, seals, and components to complete the installation
     
    With the mechanical work wrapped up in the shop, John strapped her down to the rollers for Vlad to perform a custom Flex Fuel calibration via COBB Tuning’s Accessport V3. With 93 octane in the tank, Vlad increased output to a conservative 330.62awhp & 345.89lbft, and then with E85 in the tank and the stock turbocharger at full tilt, output increased to a ripping 361.79awhp & 384.36lbft! Stock turbocharger delivering the jam!
     

     
    Reach Out Today To See What We Can Do For You!